(+86)13857177505
Email: cw@zjtongbao.com

Product was successfully added to your shopping cart.

Vibratory Finishing Machine

Machines For Vibratory Finishing

Parts are rarely complete after primary fabrication. More often than not, a part will require one or more finishing processes before it can be considered properly completed.

Vibratory finishing is one such metal finishing process. It can be used to deburr, descale, burnish, and clean metal parts after fabrication. Tongbao Equipment Company, metal finishing specialists for more than 20 years, carries a full line of vibratory finishing equipment including bowl, tub, and continuous models.

Process

The vibratory finishing process uses specially shaped abrasive media to achieve the desired finishing effect. First, the abrasive media are placed into a container along with the parts to be finished; next, an off-center rotating weight spins within the container, causing the tub to shake and vibrate.

The cyclical vibration of the tub lifts and drops the container’s contents repeatedly in rapid succession. This causes the abrasive media to interact with the metal parts in a way that is very similar to standard filing — where the media comes into contact with the part, the surface is eroded and smoothed until achieving the desired finish.

Vibratory finishing is a batch operation, suited to processing large sets of relatively small workpieces. Because the vibratory action moves the entire load as a single unit, it is ideal for finishing parts that are more fragile — the forces within the abrasive media and parts are equal, eliminating the risk of tearing and other part distortion. Many vibratory finishers can be opened while in use, enabling trained workers to visually inspect parts during the ongoing finishing process.

The vibratory finishing process can create a range of different finishes on parts. The finish can be controlled by varying the frequency and amplitude of the vibratory finishing equipment. Typical frequencies range from 900 to 3,600 cycles per minute (CPM); amplitude, the difference between the highest and lowest point of the cycle, can vary from 0 to 4.76 millimeters.

Media

Media used in vibratory finishing equipment can vary; selection of such media depends on the type of finish that your project requires. Some types of finishing media can include:

Ceramic Tumbling Media — Used for general purpose polishing and deburring, ceramic tumbling media is best suited for heavy cutting and hard metal parts. Use ceramic abrasive media for more aggressive polishing, deburring, and cleaning, or for the removal of oil and grease. Precision ceramic media can perform the same functions but for smaller products.

Steel Shot — Shot made from stainless or carbon steel is an ideal media for polishing and burnishing metal parts. It produces a bright shine without removing any metal from the parts, plus its heavy weight can sometimes reduce finishing time.

Plastic — Though it can be used for several different applications, plastic abrasive media is best suited to polishing, burnishing, or otherwise brightening a part. Plastic abrasive media generally requires specialized soap, chemicals, or other cleaning compounds.

Contact us today to learn more about our vibratory finishing equipment.

 

                              Vibratory Finishing Machine                                                             Vibratory Finishing Machine With Separator

 

Vibratory Finishing Machine With Cover

 

Vibratory Finishing Machine

Set Ascending Direction

   

Items 1 to 10 of 15 total

  1. 1
  2. 2
  1. TB-60A,TB-80A,TB-150A,TB-200A,TB-300A,TB-400A,TB-600A,TB-900A

    TB-150A,TB-200A,TB-300A,TB-400A,TB-600A,TB-900A
  2. TB-150B,TB-200B,TB-300B,TB-400B,TB-600B

    TB-150B,TB-150B,TB-200B,TB-300B,TB-400B,TB-600B
  3. TB-150C,TB-200C,TB-300C,TB-400C,TB-600C,TB-900C

    TB-150C,TB-200C,TB-300C,TB-400C,TB-600C,TB-900C
  4. TB-60(A)Vibratory Finishing Machine

    TB-60(A) is a standard model with a capacity of 13 uk gal which contains no separator.

    The specification size of the machine is 28 by 28 by 30 inch, and the weight is 220 lb.

    The motor power of the machine is 0.75 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.47 inch.

  5. TB-80(A)Polishing Machine

    TB-80(A) is a standard model with a capacity of 18 uk gal which contains no separator.

    The specification size of the machine is 31 by 31 by 31 inch, and the weight is 265 lb.

    The motor power of the machine is 1.1 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.47 inch.

  6. TB-120(A)Polishing Machines

    TB-120(A) is a standard model with a capacity of 26 uk gal which contains no separator.

    The specification size of the machine is 43 by 43 by 37 inch, and the weight is 397 lb.

    The motor power of the machine is 2.2 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.79 inch.

     

  7. TB-150(B)Vibratory Polishing Machine

    TB-150(B) is a model with a capacity of 33 uk gal which contains a separator.

    The specification size of the machine is 46 by 43 by 37 inch, and the weight is 441 lb.

    The motor power of the machine is 2.2 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.79 inch.

  8. TB-200(A)Grinding Machine

    TB-200(A) is a standard model with a capacity of 44 uk gal which contains no separator.

    The specification size of the machine is 47 by 47 by 37 inch, and the weight is 617 lb.

    The motor power of the machine is 2.2 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.79 inch.

  9. TB-250(B)Polisher

    TB-250(B) is a model with a capacity of 55 uk gal which contains a separator.

    The specification size of the machine is 51 by 47 by 37 inch, and the weight is 661 lb.

    The motor power of the machine is 2.2 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.79 inch.

  10. TB-300(A)Surface grinding machine

     

    TB-300(A) is a standard model with a capacity of 66 uk gal which contains no separator.

    The specification size of the machine is 53 by 53 by 43 inch, and the weight is 1213 lb.

    The motor power of the machine is 3.7 Kw, and the motor speed is 1450 r/min.

    The thickness of the machine’s lined with PU container 0.79 inch.

Set Ascending Direction

   

Items 1 to 10 of 15 total

  1. 1
  2. 2